Table of Content
Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen. Don't open the display more than 90º—it is still connected to the top of the phone by the display, digitizer, and front camera cables which can tear easily. Gently grasp the display assembly and lift it up to open the phone, using the clips at the top of the front panel as a hinge.
While firmly pulling up on the suction cup, slide the edge of the spudger under the bottom left corner of the display. While still maintaining pressure on the suction cup, insert the flat tip of a spudger into the gap, directly above the headphone jack. Apply just enough pressure to create a small gap between the display assembly and the rear case. Opening the display on the 6s Plus separates a thin strip of adhesive around the perimeter of the display. If you prefer to replace the adhesive, have a set of new adhesive strips ready before you continue. It's possible to complete the repair without replacing the adhesive, and you probably won't notice any difference in functionality.
Taping Over The Display
I work at an Apple repair centre in based in the UK and we have recently encountered MAJOR issues with replacement home buttons. It turns out that home buttons are linked too the logic board on each handset due to the method in which Apple stores you biometric data. Due to this, to the greatest extent of our knowledge, any update will cause an ERROR 53 to occur. As of yet we have not be able to rescue a handset from this state.
Optionally, apply mild heat to the lower edge of the iPhone using an iOpener or hair dryer for about a minute. You can also use this guide to replace the home button bracket. Use a set of tweezers to carefully pull the gasket up from the home button. There is power on the second logic-board connector from top, misplacing it while assembly can cause short circuit. Your replacement part may come with an extra Phillips screw already installed left of the Home Button.
Lot of iPhone 6, 6+, 6s, 6s+, LCD Screens With Digitizers - Black And White 1 Ea
Remove the unnecessary screw so that you can reinstall the home button bracket. If you are replacing a broken front panel, there may be glass shards stuck to the home button. Carefully remove any remaining glass before transferring your home button to a new display.
If you aren't using the iSclack, skip down three steps for an alternate method. Using a set of tweezers, carefully pull the gasket up and off of the home button carefully so you don’t snag it on the home button cable. You also have to remove the aluminum plate and the rear camera/speaker assembly. After reassembly, connect the iPhone to an AC power source before turning it on for the first time. Once the iPhone has booted up successfully, you can disconnect the AC power.
NEW Broadcom Touch IC Chip BCM5976C0KUB6G BCM5976 u12 for Repair iPhone 5/5S/5C
The information that comes from the digitizer transfers through a digitizer flex cable to an LCD. Whether you have an iPhone 6 or iPhone 6 Plus, there are specific digitizer to fit your phone and for proper screen replacement. You can obtain an individual screen or a pack that has multiple digitizers for whenever you need to repair your phone or help with the replacement of another phone. Repair kits come with all the necessary tools and equipment necessary to perform a screen replacement. For anyone who has damaged their iPhone 6 Plus screen from either deep scratches or having it badly cracked, screen replacement is a necessity but also a headache. The replacement of a screen can sometimes be costly especially for larger smartphones with bigger screens like the iPhone 6 Plus.
To reassemble your device, follow these instructions in reverse order. Remove the home button bracket from the front panel assembly. Remove the two 1.8 mm Phillips screws securing the home button bracket to the front panel. During reassembly, align the clips just below the top edge of the rear case. Then, slide the front panel upward until its top edge is flush with that of the rear case.
For Black iPhone 6 Plus LCD Display Touch Replacement w Tools+ 2X Protectors!
While still supporting the front panel, use a fingernail or the edge of an opening tool to disconnect the front-facing camera and earpiece speaker connector. While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case. Center the suction cups and press them firmly onto the top and bottom of the iPhone.
Press a suction cup onto the screen, just above the home button. The next two steps demonstrate using the iSclack, a great tool for safely opening the iPhone 6 Plus that we recommend for anyone doing more than one repair. No, the fingerprint scanner and logic board are paired during their manufacturing so if the original scanner is destroyed, you will never have Touch ID again.
We also offer a mail-in repair service for customers who can’t get to a local store. If paying $200.00 is not in your budget to repair your broken home button, shopping for the best price is going to save you time, money, and headaches. Some services like iFixandRepair are charging $70.00, and Genius Phone Repair is quoted at $104.99 to fix an iPhone 6/6 Plus home button. To reassemble your iPhone 6/6 Plus, simply follow these instructions in reverse order and you have officially fixed your iPhone’s broken home button. Gently peel back the home button the rest of the way off of the display with the spudger tool. Power off your iPhone 6/6 Plus and remove the two 3.6 mm pentalobe screws next to the lighting connector or where you commonly plug your phone in.
The only problem I experienced was that you have to re-use the black gasket around the home button. It was tricky to have to place it on the new home button, but I got it after a few tries. Bend the connector back to ensure it doesn't make contact and power the iPhone on while you're working on it. Insert the flat tip of the spudger under the right edge of the display. Slide the tip of the spudger up the left side of the phone, between the front panel and the rear case. The safest place to pry from is the notch in the front panel above the headphone jack.
Several clips along the top edge of the front panel form a partial hinge, allowing the front panel assembly to swing open like a book. Open the display to about a 90º angle, and lean it against something to keep it propped up while you're working on the phone. Pull the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.
If you’re within your one-year Apple Care warranty, Apple will charge you $79.00 to repair your broken home button. If your Apple Care warranty has expired, expect to pay approximately $200.00 for all iPhone 6/6 Plus home button repairs. Using the top of the phone as a hinge, pull the home button end of the front panel away from the rear case. Release the power button and then press and hold the home button until the, “slide to power off” slider vanishes. Repeatedly slamming your finger into a broken, sticky, or burning hot iPhone 6/6 Plus home button won’t magically fix your crippled device.
Using your fingertip, gently press up on the home button from the front side of the display assembly. Use firm, constant pressure to slowly separate the home button's rubber gasket from the front panel. In the next four steps, take care to pry up only on the cable connectors, and not on their sockets on the logic board. Use a clean fingernail or the edge of an opening tool to gently pry the battery connector up from its socket on the logic board.
If any body has any further knowledge it would be massively appreciated, as a community we need to get to the bottom of this before anybody had any major disasters. Will the short circuit damage the logic board or the camera / earpiece assembly? I'm worried just encountered this very issue even though the phone was off. Hold the iPhone firmly with one hand, and with the other, pull up on the suction cup to slowly separate the front panel assembly from the rear of the case.
